Camera bodies
GoPro MISSION 1 PRO ILS hard case with custom foam
The short answer
The GoPro MISSION 1 PRO ILS measures 89.6 × 58.7 × 58.1 mm. On its own it fits the S compact case: €189, case and cut foam included, delivery included, in 4 to 6 weeks.
The gear is not included.
- Cutting plan approved by you before production
- Delivery included, with tracking number
- Two-year legal guarantee of conformity
- Secure payment by Shopify
Hard camera case: which one for your camera?
- Dimensions used
- 89.6 × 58.7 × 58.1 mm
- Stored as
- body cap on, +12 mm of depth (margin included)
- Dimension reliability
- To confirm 46/100
- Clearance left in the foam
- 4.5 mm per side
- Weight
- 197 g
- Pocket depth
- 61 mm
- Delivered cases
- no delivered case recorded for this gear yet
- Sources
- manufacturer spec sheet
Our sources are not yet enough to guarantee these dimensions to the millimetre: we will ask you to check your GoPro MISSION 1 PRO ILS’s measurements before cutting, and we leave a little more clearance.
How to read these dimensions, their sources and their reliability: see the FAQ
Start from a kit with the GoPro MISSION 1 PRO ILS
Take the set closest to yours, then adjust it in the configurator.
Everyday
- GoPro MISSION 1 PRO ILS
- SD card wallet
- Samsung T7
- Panasonic Lumix G Leica DG Vario-Elmarit 12-35mm F2.8 II ASPH Power OIS
- 5-inch monitor
S compact case, €189
Full kit
- GoPro MISSION 1 PRO ILS
- SD card wallet
- 2 × Samsung T7
- Panasonic Lumix G Leica DG Vario-Elmarit 12-35mm F2.8 II ASPH Power OIS
- 5-inch monitor
- Panasonic Lumix G Leica DG Vario-Elmarit 35-100mm F2.8 II ASPH Power OIS
- RØDE VideoMic NTG
- DJI Mic 2 (charging case)
- Pocket: crab clamp
M all-round case, €259
How it is stored
The body is stored upright, on its base, with the cap on: the screen and mount do not rest on the foam. If the case’s foam is too thin for its height, it lies on its back, mount facing up.
Size and price
The pocket cut for the GoPro MISSION 1 PRO ILS
In the S case, the foam is cut at 68 × 99 mm on the floor for the GoPro MISSION 1 PRO ILS: its dimensions used plus 4.5 mm of clearance on each side. The pocket goes 61 mm deep.
- Pocket footprint
- 68 × 99 mm
- Pocket depth
- 61 mm
- Foam under the pocket
- 41 mm
- Space left along the length
- 232 mm
- Space left across the width
- 128 mm
- Share of the inside volume used
- 4.6 %
Margins: inside of the S case (300 × 227 × 132 mm) minus the pocket.
Where these dimensions come from
One line per source consulted. The cut adds the storage margin to it.
| Type | Website | Published dimensions | Weight | What the dimensions leave out |
|---|---|---|---|---|
| manufacturer spec sheet | gopro.com | 89.6 × 58.7 × 46.1 mm | 197 g | the body cap |
- No cross-check possible: a single source describes these dimensions in the same state.
Compared with similar models
Gap = dimension of the nearby model minus that of the GoPro MISSION 1 PRO ILS: + larger, − smaller.
The Sony RX100 VII measures 15.5 mm less in depth than the GoPro MISSION 1 PRO ILS. Same recommended case size for both: the S.
| Model | Width (mm) | Height (mm) | Depth (mm) | Weight (g) | Recommended case |
|---|---|---|---|---|---|
| Sony RX100 VII | +12 | −0.5 | −15.5 | — | S |
| Blackmagic Micro Studio Camera 4K G2 | −5.5 | +7 | +19.5 | +103 | S |
| Sony ZV-1 | +16 | +1.5 | −14.5 | — | S |
| Blackmagic Micro Cinema Camera | −7 | +6.5 | +19.5 | +115 | S |
Often stored with the GoPro MISSION 1 PRO ILS
Where foam is left over, the configurator suggests a pocket of the right size. Nothing is added by default.
Spare batteries
Empty pocket for your own, at no extra cost · 90 × 60 mm
Foamd SD card wallet
Sold with its pocket, €12 · 115 × 85 mm
Charger
Empty pocket for your own, at no extra cost · 110 × 75 mm
Foamd lens cleaning kit
Sold with its pocket, €15 · 170 × 95 mm
Questions about the GoPro MISSION 1 PRO ILS case
- Which case size for the GoPro MISSION 1 PRO ILS?
- On its own, the GoPro MISSION 1 PRO ILS fits in the S case (300 × 227 × 132 mm inside), at €189 for case and foam, delivery included. Its pocket is 61 mm deep in 102 mm foam.
- How much clearance does the foam leave around the GoPro MISSION 1 PRO ILS?
- 4.5 mm per side. Our sources are not yet enough to guarantee them to the millimetre: we will ask you to check your measurements before cutting.